-7%
,

SpeedyBee F405 V3 BLS 50A 30×30 FC&ESC Stack

Availability:

In Stock


$69.99 $74.99

In Stock

SpeedyBee F405 V3 BLS 50A Stack

So so many cool features,
at an unbelievable price!

SpeedyBee F405 V3 STACK

$69.99 for a Bluetooth 50A
Stack? That’s ridiculous
I know right? With only $69.99, you will get an STM32F405 FC
(better than F411), onboard 4-level battery life indicator, 4GB
Blackbox SD card slot for your flight logs, 4 groups of LED strip pads,
complete with a DJI plug for your digital quad, and built-in Bluetooth
for wireless configuration on the SpeedyBee app.
Don’t forget about the powerful 50A 4-in-1 ESC, built with TVS
protective diode + Japan made TDK SMT capacitors + external
1500uF low ESR capacitor, everything is for durable build and
smooth flight.
All of that for only $69.99! Top-shelf spec at a crazy low price, what
are you waiting for?

SpeedyBee F405 V3 STACK

Configure your FC and ESC
via Bluetooth
With SpeedyBee app, turn your phone into an all-in-one
FC configurator and tune your quad anytime, anywhere.
Experience wireless, fully configurable ESC experience with
SpeedyBee app.

SpeedyBee F405 V3 STACK

Powerful Real 50A 4-in-1 ESC!
Built with the robust BB21 MCU and large motor pads for easy
soldering. Built with Japan made TDK filtering SMT capacitors +
onboard TVS protective diode, brings smooth flight experience.
Real 50A output, ready for your baddest 6S motors.

SpeedyBee F405 V3 STACK

Forgot your LiPo checker?
Just look at the FC!
Built with a 4-level LED battery indicator, now you can fly
anywhere worry-free – even without your lipo checker!

SpeedyBee F405 V3 STACK

8 motors output for X8/Y6/
fixed-wings
You could use this stack to build your X8 drones, Y6 drones or
fixed wings. Forget about crawling through your massive build
just to plug in that USB cable. Just take out your phone to
configure everything in the SpeedyBee app.

SpeedyBee F405 V3 STACK

Change motor directions
wirelessly!
Finishing your latest build? Just replaced your motor after a crash?
Take your smartphone out, and configure your motor direction
wirelessly with the latest SpeedyBee app. Works for all
BLHeli32 / BLHeli_S / BlueJay ESCs.

SpeedyBee F405 V3 STACK

4 sets of LED pads with
simple switching
Need more visibility at night? Just solder up your LED strips*
and blaze the darkest trail you can find. With just one tap on t
he BOOT button, you can cycle through all different LED presets**
and pick the one you love!
* LED strips could be purchased here
**Or long press the boot button to switch to Betaflight LED mode

SpeedyBee F405 V3 STACK

1500uF Low ESR capacitor +
TVS protective diode =
Extra protection
The ESC is built with TVS protective diode to absorb the voltage
spike when you plug in the battery, or during crashes that block
your props.We also provide a humongous 1500uF low ESR
capacitor, ensuring clean data from the gyro to the FC.

SpeedyBee F405 V3 STACK

And packaged with more
useful features
● Built-in barometer for accurate height calculation
● SD Card slot can support up to 4GB Blackbox data*
● Dedicated DJI Air Unit connector for a quick digital build
● 9V 2A + 5V 2A individual BECs
● 4 x UARTs for your receiver + VTX + camera + GPS.
● Power your GPS with a USB cable – no battery needed.
No extra heat, no worries.
● 22mm cutouts for FPV camera in your tight build
*Betaflight firmware requires the type of the microSD card to be
either Standard (SDSC) or High capacity (SDHC), so extended
capacity cards (SDXC) are not supported(Many high-speed U3 cards
are SDXC). Also the card MUST be formatted with the FAT16 or FAT32
(recommended) filesystems. So, you could use any SD card less than
32GB, but the Betaflight can only recognize 4GB maximum.
We suggest you use this 3rd party formatting tool and choose
‘Overwrite format’ then format your card. Also check out here for
the recommended SD cards or buy the tested cards from our store.

SpeedyBee F405 V3 STACK

Dimensions

SpeedyBee F405 V3 STACK

Wiring Diagram

SpeedyBee F405 V3 STACK

SpeedyBee F405 V3 STACK

SpeedyBee F405 V3 STACK

SpeedyBee F405 V3 STACK

SpeedyBee F405 V3 STACK

Specifications
Product NameSpeedyBee F405 V3 30×30 Flight Controller
MCUSTM32F405
IMU(Gyro)BMI270
USB Port TypeType-C
BarometerBuilt-in
OSD ChipAT7456E chip
BLE BluetoothSupported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
DJI Air Unit Connection WayTwo ways supported: 6-pin connector or direct soldering.
Blackbox MicroSD Card Slot*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose ‘Overwrite format’ then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.
BetaFlight Camera Control PadYes(CC pad on the front side)
Current Sensor InputSupported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
Power Input3S – 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
5V Output9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
9V Output2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
3.3V OutputSupported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V OutputSupported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC SignalM1 – M4 on bottom side and M5-M8 on front side.
UART6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection), UART5(Dedicated for ESC telemetry)
ESC TelemetryUART R5(UART5)
I2CSupported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED PadSupported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
BuzzerBZ+ and BZ- pad used for 5V Buzzer
BOOT ButtonSupported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI InputSupported. Named as RS on the front side.
SmartPortUse any TX pad of UART for the SmartPort feature.
Supported Flight Controller FirmwareBetaFlight(Default), EMUFlight, INAV
Firmware Target NameSPEEDYBEEF405V3
Mounting30.5 x 30.5mm( 4mm hole diameter)
Dimension41.6(L) x 39.4(W) x 7.8(H)mm
Weight9.6g
Product NameSpeedyBee BLS 50A 30×30 4-in-1 ESC
FirmwareBLHeli_S JH50
Wireless ConfigurationFull Configuration Supported in the SpeedyBee app
PC Configurator Download Linkhttps://esc-configurator.com/
Continuous Current50A * 4
Burst Current55A(5seconds)
TVS Protective diodeYes
External Capacitor1500uF Low ESR Capacitor(In the package)
ESC ProtocolDSHOT300/600
Power Input3-6S LiPo
Power OutputVBAT
Current SensorSupport (Scale=386 Offset=0)
Mounting30.5 x 30.5mm( 4mm hole diameter)
Dimension45.6(L) * 44(W) * 6.1mm(H)
Weight13.8g
SKU: BS066-050 Categories: ,
Weight0.1 kg

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “SpeedyBee F405 V3 BLS 50A 30×30 FC&ESC Stack”

There are no reviews yet.