, , ,

SpeedyBee F7 V3 BL32 50A 30X30 Stack BMI270 F722 Flight Controller BLHELI32 50A 4in1 ESC 3-6S for FPV Freestyle Drones DIY Parts


In Stock


Product NameSpeedyBee F7 V3 Flight Controller
USB Port TypeType-C
OSD ChipAT7456E chip
BLE BluetoothSupported. Used for Flight Controller configuration
Flash FC Firmware WirelesslySupported. Please enter MENU > FC Firmware Flasher
Download/Analyze BlackboxSupported.Please enter MENU > Blackbox Analyzer
DJI Air Unit Connection WayTwo ways supported: 6-pin connector or direct soldering.
Flash(for BlackBox)500MB
BetaFlight Camera Control PadYes(CC pad on the front side)
Power Input3S – 6S Lipo
5V Output10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.
9V Output2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.
3.3V OutputSupported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V OutputSupported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal PadsM1 – M4 on bottom side and M5-M8 on front side.
UART5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)
ESC Telemetry UARTR4(UART4)
I2CSupported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
LED PadUsed for WS2812 LED controlled by Betaflight firmware.
BuzzerBZ+ and BZ- pad used for 5V Buzzer
BOOT ButtonSupported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI InputSupported. Named as RS on the front side.
SmartPortUse any TX pad of UART for the SmartPort feature.
Supported Flight Controller FirmwareBetaFlight(Default), EMUFlight, INAV
Firmware Target NameSPEEDYBEEF7V3
Mounting30.5 x 30.5mm( 4mm hole diameter)
Dimension41(L) x 38(W) x 8.1(H)mm
Product NameSpeedyBee BL32 50A 4-in-1 ESC
FirmwareSpeedyBee BL32 50A
Configurator Download Linkhttp://github.com/bitdump/BLHeli/releases
Continuous Current50A * 4
Burst Current55A(5S)
TVS Protective diodeYes
Heat SinkYes
External Capacitor1500uF Low ESR Capacitor(In the package)
ESC ProtocolDSHOT300/600
Power Input3-6S LiPo
Power OutputVBAT
Current SensorSupport (Scale=490 Offset=0)
Mounting30.5 x 30.5mm( 4mm hole diameter)
Dimension45.6(L) * 40(W) * 8.8mm(H)
Weight19.2g with heat sink


F7V3, BL32 50A, F7V3 BL32 50A

Based on 0 reviews

0.0 overall

Be the first to review “SpeedyBee F7 V3 BL32 50A 30X30 Stack BMI270 F722 Flight Controller BLHELI32 50A 4in1 ESC 3-6S for FPV Freestyle Drones DIY Parts”

There are no reviews yet.